Picture of the Pairing and Volume Down buttons on the speaker.

How to Factory Reset Sony XE200

Show you how to factory reset your Sony XE200 portable BT speaker to its default settings. Factory resetting restores the XE200 to factory default state. Plus, doing this erases any earlier paired Bluetooth devices from memory. We might want to clear these to prevent this speaker from pairing to any nearby Bluetooth devices. Also, you would best reset the unit to get it ready for sale or re-gifting, or to stop it from pairing with devices you no longer wish it to connect with.

How to Factory Reset Sony XE200, Step by Step

1. Turn ON the Speaker

Press and release the Power button for a half-second or so. Find this button as we show in the next picture.

Picture of the Power button on the Sony XE200.
The Power button on the Sony XE200.

Then, the status light comes on, as we see next.  This light we find just to the left of the Power button near the top of the speaker on the buttons panel.

Picture of the green glowing power lamp on the Sony XE200.
The green glowing power lamp on the Sony XE200.

The speaker makes a rising electronic sound when it powers up, whether it connects to a nearby device or not. But whether it pairs or not, this reset routine works the same, as follows.

2. Press and Hold the Volume DOWN and Pairing Buttons

Both of these buttons we find on the panel in the back of the speaker, as called out in the next picture. Counting from the top, the Pairing button is the second button down from the top, just below the Power button.  And, the Volume Down button is the fifth one down from the top, just below the Volume UP (+) button, and just above the BATT button.

Picture of the Pairing and Volume Down buttons on the speaker.
The Pairing and Volume Down buttons on the speaker.

Then, hold both buttons in until all lamps go out, the unit plays a power-off sound, and then the speaker shuts down completely.  This takes around five seconds as the speaker factory resets.

Next, the speaker powers OFF, and the Power and Pairing lamps go dark, as shown next.

Picture of all the lamps being dark on the Sony XE200.
All lamps are dark on the Sony SRS XG200 speaker.

You may release the buttons when all the lights go dark.

3. Check that your Sony XE200 Did Indeed Factory Reset

Next, power on the XB 200 once more, as described in step 1 above.

Note that after a factory reset, this speaker comes up in pairing mode. The Pairing lamp blinks in a pulse-pulse-pause, pulse-pulse-pause pattern to tell you this.  This is a signal for you to look for this speaker on a nearby BT device, and pair to it if you so desire.

4. Done with How to Factory Reset Sony XE200 !

The factory reset is now complete. So you may now sell or gift the unit, or pair it again with your favorite Bluetooth devices.

After a factory reset, the speaker no longer automatically connects with any previously paired device. Thus, to restore this auto syncing, you manually pair the XE200 with a device. Then after that, any time that both speaker and that device have Bluetooth ON, and they’re near to each other, pairing would automatically take place once more.

Other Sony XE200 Posts

    1. Sony XE200 Firmware Update
    2. Sony XE200 Bluetooth Pairing
    3. Sony XE200 Specs Watts
    4. Sony XE200 Power Button Not Working
    5. How to Connect Sony XE200 to iPhone
    6. Sony XE200 Reset
    7. Sony XE200 Specs
    8. How to Pair Sony XE200 to iPhone
    9. How to Tell if Sony XE200 is Charging
    10. Sony XE200 Software Update

Related Posts to How to Factory Reset Sony XE200

    1. How to Factory Reset Sony XB21
    2. How to Factory Reset Sony XB23
    3. How to Factory Reset Sony XB30
    4. How to Factory Reset Sony XB41
    5. How to Factory Reset Sony XB22

References

    1. Official Sony XE200 Support Page
    2. Where to Buy the Sony XE200

Revision History

    • 2023-03-29: First published.