Picture of the front of the Wonderboom 1.

How to Run Battery Check on Wonderboom 1

Describes How to Run Battery Check On Wonderboom 1, and also, how to know if the battery life is shortening over time.

How to Run Battery Check on Wonderboom 1: Step by Step

1. First, Turn ON the Wonderboom 1 

You won’t be able to read battery charge status unless the speaker is ON.

Picture of the Wonderboom 1 top view. Showing the dark -Power- button.
The Wonderboom 1 top view. Showing the dark -Power- button.

To turn on the speaker, press and release the Power button, circled in the last picture.

The little lamp in that button should then come on, as shown next, and the speaker should make its startup sound.  If it does not, then the battery could be completely dead.

Picture of the glowing -Power- button, which you can read to check Wonderboom 1 battery.
The glowing -Power- button, which you can read to check Wonderboom 1 battery.

But as long as there’s some juice in the battery, the speaker should power up.  When it does, move on to the next step.

2. Press and Release the Volume UP and Volume DOWN Buttons to Continue with How to Run Battery Check on Wonderboom 1

Press and release the center areas of the Volume UP and Volume DOWN buttons at the same time.  Find these areas in the picture shown next.

Picture of the Volume UP(+) and Volume DOWN (-) buttons. Press these to run a battery check.
The Volume UP(+) and Volume DOWN (-) buttons. Press these to run a battery check.

When you press these buttons together, the speaker makes one to four “blunk” sounds to tell you how full the battery is.  Four blunks means that the battery has between 75 and 100 percent charge.  Three blunks, and the battery has between 50 and 75 percent charge.  Two blunks denotes that you have between 25 and 50 percent charge in the speaker’s battery.  And finally, one blunk means between 0 and 25 percent charge.

Also, when the Wonderboom 1 battery gets critically low, the Power lamp starts flashing red.

Press these buttons any time the speaker is ON, to check how full the battery is.  The number of blunks you hear, lets you roughly guess how much time you have left to play the speaker, before it goes dead.  Since a fully charged Wonderboom 1 plays for roughly ten hours.  So four blunks means that the speaker has between 7.5 and 10 hours of play time left before it goes dead.  Three blunks means that it will play for another 5 to 7.5 hours.  Two blunks means between 2.5 and 5 hours of music time left.  And 1 blunk means that you’ll get between 0 and 2.5 more hours of play time.

3. How to Run Battery Check on Wonderboom 1: The Details

When the unit is new, and using a full power USB charger, the Wonderboom 1 charge time is about 2.8 hours to reach a full charge.

And, the fully charged battery should last for around ten hours of play time before going dead.

A sign of a bad battery, is that it goes dead too fast, or takes too little or too much time to fully charge. So if you fully charge your speaker, but it only plays for under eight hours before dying, its battery may be bad, and unable to hold a full charge anymore.

Picture of the -Power- button glowing steady red.
The -Power- button glowing steady red.

If the Wonderboom 1 battery takes longer than three hours to completely recharge, this could also mean a failing battery.  It could mean too that the charger you’re using is not strong enough to recharge the speaker in the specified charge time of 2.8 hours.

Also, slow charging can happen because your charge cord is too thin.  So for best results, we suggest using a full-current USB cable (one that easily carries 2.1 amps). 

Other Wonderboom 1 Posts

    1. The Buttons Explained
    2. How to Charge
    3. How to Pair to iPhone
    4. Not Turning ON Fixing
    5. Blinking White Light Explained

References for How to Run Battery Check on Wonderboom 1

    1. Official Wonderboom 1 Support Page
    2. Where to Buy the Wonderboom 1