This post gives JBL Boombox factory reset instructions, that restore the speaker to its default factory settings. Factory resetting the Boombox restores it to fresh-out-of-the-box operation. It clears any earlier paired Bluetooth devices from memory. Wiping old settings stops the BT speaker from pairing to any close-by active Bluetooth devices. Also, you might factory reset to prepare the speaker for sale or re gifting, or to stop it from pairing with phones and tablets you no longer wish it to link with.
JBL Boombox Factory Reset Instructions, Step by Step
1. Turn on the Boombox
When the speaker is off, all buttons are dark, including the Power button, as shown next.
Then, press and release the Power button. That button should right away light up as shown in the following pictures. Find the Power button, as shown in the last picture above near the center of the photo.
Next, the Power button comes on, as shown next. It either blinks or flashes depending on pairing state.
2. Wait for the Power Up Sound
The speaker makes a rising electric guitar strum sound when it powers up. You may begin the JBL Boombox factory reset after this sound ends.
Now if your speaker pairs with an in-range Bluetooth device, you’ll also hear the three rising single guitar notes a few seconds after the startup cord. At any rate, whether or not the speaker pairs with any Bluetooth devices does not change the reset routine. In either case, the JBL Xtreme factory reset directions remain the same, as we list next.
3. Press the Volume UP and Play-Pause Buttons Together
See the next picture to find the Pause Play and UP Volume buttons.
The Boombox then enters factory reset, as seen in the next picture.
Note that both the Power and Connect+ buttons come on for a couple seconds as the reset advances. The Power button glows a pale blue or white, and the Connect+ button glows gray-white for a second or two, and then the speaker powers down and all buttons go dark, as shown next. You’ll also hear the falling guitar strum as the unit shuts off.
4. Next, Check that the JBL Boombox Factory Reset Did Indeed Occur
Next, power on the Boombox again, as shown in step 1 above. In summary, press and release the Power button. See the Power button pointed out in the next picture.
Now this time, after JBL Boombox factory reset, our speaker right away starts in Bluetooth pairing mode, as seen next.
Note that we did not press the Bluetooth button first. Why? Because after reset, the speaker automatically enters Bluetooth pairing mode. Note that the Power button blinks blue to mean Bluetooth discovery mode. When the Power button blinks blue or shows as solid white, the speaker is not currently paired. We expect it would not pair to anything after resetting.
5. Done with JBL Boombox Factory Reset
Finally, the reset is now complete. So, you may pack the speaker up for resale, or pair it once again with your media playing Bluetooth devices.
Note about Automatic Pairing after JBL Boombox Factory Reset
The Boombox will no longer pair with any previously paired in-range Bluetooth device without you manually pairing it again. So, to restore automatic Bluetooth pairing, you’ll need to forget the previously paired connection for this speaker listed in the Bluetooth devices section of your source device settings. Next, once that’s done, then manually pair the Boombox with that device again if you wish. Then any time that both speaker and that device have Bluetooth turned on, pairing automatically happens once again.
Related Posts to JBL Boombox Factory Reset Instructions
- Amazon Dot 2 Reset Instructions, Hard Factory Reset
- JBL Charge 4 Reset Instructions, Hard Factory Reset
- JBL Xtreme 2 Factory Reset Instructions
- Flip 5 JBL Speaker Factory Reset Instructions
- JBL Go 3 Factory Reset Instructions
Other Posts About the JBL Boombox Power Bank Bluetooth Speaker
- How to Bass Boost JBL Boombox BT Speaker
- JBL Boombox Volume Control Explained
- Boombox JBL Speaker Low Frequency Mode, Extra Bass
- JBL Boombox Infinity Button Explained
- 2021-07-26: First published.