In this JBL Wonderboom controls guide, we discuss all controls on this speaker, the functions, meanings, and codes and combinations to press them to get different things to happen, We show where they are on the speaker with many pictures. Further, we explain what each button does when you press it, and when to press it to accomplish typical BT speaker tasks. We also detail the two status lamps and the USB charger input below.
The JBL Wonderboom has five controls on the top and front, two lamps in those buttons, one USB port on the back behind a water tight cover. The status lamp glows in one color and flashes to show speaker charging going on. We also find a lamp in the Bluetooth button that shows BT pairing status.
First off, this control switches the JBL Wonderboom ON and OFF. This button also contains an LED that shows power and battery status. When the speaker is ON, and the battery has at least a little charge, this lamp glows solid white. But when the battery falls to too-low status, this lamp glows solid red. This means that it’s time to put the BT speaker on the charge before it shuts off all the way.
Next, we have the Bluetooth discovery mode button, as highlighted in the next picture. This is the smaller of the two raised panel controls.
With this JBL Wonderboom turned on, press the Bluetooth button. This places the speaker into pairing / discovery mode. When in this mode, the speaker sends its name and other connection information over the BT radio medium, allowing nearby Bluetooth devices to find it, and then connect to it.
When speaker is in pairing mode, this button rapidly flashes white. Then after the speaker connects, this button glows steady white for several seconds, to tell that pairing was successful. Then, it goes OFF to save battery power. It stays OFF as long as the wireless connection continues. Note though that this button does not light up when you power ON the speaker is powered ON but do not pair it. Again, it only lights prior to pairing, in discovery mode, and for a brief time after you establish pairing.
The Play / Pause button is kind of hidden on the top of the JBL Wonderboom, as there is no visual icon embossed on this panel for it, unlike the other two controls, that are embossed, and raised as well. This button is not raised, though you can find it just beneath the Ultimate Ears logo. Press near the center of the logo to stop or resume playback.
Finally, you can skip forward to the next song in a playlist with the Play-Pause button on the JBL Wonderboom. As the song plays, do the following…
The JBL Wonderboom has volume controls too. What wireless speaker doesn’t? Find these on the front. These controls are shaped as large minus and plus symbols, They’re white colored on our speaker. They lower and raise the speaker volume. See the volume controls, circled in green, in the next picture. These controls never light up, and the easiest places to press to get them to work, are in the centers of the controls.
Pressing the Volume Down (-) and Power controls together for five to eight seconds, with the JBL Wonderboom turned on and not currently paired, triggers a factory reset.
This LED light is dark when the JBL Wonderboom is OFF and not charging. When powered ON, the status lamp glows steady white no matter whether the speaker is paired or not. Plus, It pulsates a dim-to-bright-to-dim pattern as the speaker recharges. See the Power lamp in the next picture,
The USB Power input port hides behind a sealed, flexible door on the back of the speaker, near its bottom, as pictured next.
You open this panel carefully, prying it open with a fingernail, coin, or other such small yet not too sharp instrument. Avoid overly pointy prying objects, as these can scratch the water seal around the door edges, and thus destroy the speaker’s water resistance.
This is a micro USB female plug, where your AC or car charger cord connects, in order to recharge the JBL Wonderboom, as shown next.
If you're a Spotify streaming service subscription holder, you can now listen to your playlists…
Here, we cover Unlink Spotify From Google Home Speaker. You may wish unlink (remove, delete)…
You might reset Alexa Echo Spot and return the settings to their factory default values,…
In this post, we run through how to find the Echo Spot IP address setting,…
You might reset Echo Spot WiFi to fix faulty connection behavior, put it on a…
Here, we detail our Echo Spot firmware update procedure for the Amazon Alexa Echo Spot.…