Picture of the Sony SRS XE200 Bluetooth speaker charging.

Sony SRS XE200 Factory Reset

We give Sony SRS XE200 factory reset directions here, to restore this portable BT speaker to its default settings. Factory resetting returns the XE200 to default state, which often fixes pairing errors and distorted sound. Plus, it clears any earlier paired Bluetooth devices from memory. We might want to erase these to stop this speaker from pairing to any close by Bluetooth devices. Also, you would best reset the unit to prepare it for sale or re-gifting, or to stop it from pairing with devices you no longer wish it to connect with.

Sony SRS XE200 Factory Reset, Step by Step

1. Power Up the Speaker

Press and release the Power button for a half-second or so. Find this button as we show in the next picture. It’s the topmost button in the buttons panel on the side of the unit.

Picture of the Power button on the Sony SRS XE200 speaker.
The Power button on the Sony SRS XE200 speaker.

Then, the status light comes on, as we see next.  This light we find just to the left of the Power button.

Picture of the green glowing power lamp on the Sony SRS XE200 speaker.
The green glowing power lamp on the Sony SRS XE200 speaker.

The speaker makes a rising electronic sound when it powers up, whether it connects to a nearby device or not. But whether or not it does pair, this reset procedure works the same, as follows.

2. Press and Hold the Volume DOWN and Pairing Buttons

Both of these buttons we find on the buttons panel, as called out in the next picture. Counting from the top, the Pairing button is the second button down from the top, just below the Power button.  And, the Volume Down button is the fifth one down from the top, just below the Volume UP (+) button, and just above the BATT button.

Picture of the Pairing and Volume Down buttons on the speaker.
The Pairing and Volume Down buttons on the speaker.

Then, hold both buttons in until all lamps go out, the unit plays a power-off sound, and then the speaker shuts down completely.  This takes around five seconds as the speaker factory resets.

Next, the speaker powers OFF, and the Power and Pairing lamps go dark, as shown next.

Picture of all the lamps being dark on the Sony SRS XE200 speaker.
All lamps are dark on the Sony SRS XG200 speaker.

You may release the buttons when all the lights go dark.

3. Check that the Sony SRS XE200 Factory Reset Worked

Next, power on the XB 200 once more, as described in step 1 above.

Note that after a factory reset, this speaker comes up in pairing mode. The Pairing lamp blinks in a pulse-pulse-pause, pulse-pulse-pause pattern to tell you this.  This is a signal for you to look for this speaker on a nearby BT device, and pair to it if you so desire.

4. Done with Sony SRS XE200 Factory Reset !

The factory reset is now complete. So you may now sell or gift the unit, or pair it again with your favorite Bluetooth devices.

After a factory reset, the speaker no longer automatically connects with any previously paired device. Thus, to restore this auto syncing, you manually pair the XE200 with a device. Then after that, any time that both speaker and that device have Bluetooth ON, and they’re near to each other, pairing would automatically take place once more.

Other Posts About the Sony SRS XE200

    1. Sony SRS XE200 Charging Instructions
    2. Sony SRS XE200 Buttons Guide
    3. How to Make Sony SRS XE200 Discoverable
    4. How to Know When Sony SRS XE200 is Charging
    5. How to Connect to Sony SRS XE200 Speaker

Related Posts to Sony SRS XE200 Factory Reset

    1. Sony SRS XE300 Factory Reset Diretions
    2. SRS XB40 Sony BT Speaker Factory Reset Instructions
    3. Sony SRS XB30 Factory Reset Instructions
    4. SRS X3 Sony Factory Reset Instructions
    5. Sony SRS X2 Factory Reset Directions

References for Sony SRS XE200 Factory Reset

    1. Official Product Page for the Sony SRS XE200 at Sony.com

Revision History

    • 2022-10-31: First published.