Picture of the Sony SRS XB10 Bluetooth speaker, showing the logo side.

Sony XB10 Pairing Two Speakers

Pairing two Sony SRS-XB10 Bluetooth speakers together lets you create a stereo (L + R) set, or a double set where both speakers play the same audio (mono sound on both speakers).  So in this piece, we show you how to do this to enjoy more life like sounding music from this little yet husky speaker.  The only extra cost is that you must have two XB10s to get double or stereo sound, because individually, these speakers are monophonic.

Picture of the Sony XB10 rear panel, showing the L and R lamps circled.
Sony XB10 rear panel, showing the L and R lamps circled.

Sony XB10 Pairing Two Speakers: How it Works

Prepare the Two Speakers for Pairing

    1. Start with both speakers powered OFF.
    2. Power up the first speaker, and watch for the Power / Pairing lamp to begin flashing white.
    3. Press and hold the Add button for around three seconds, until the XB10 beeps. The Power / Pairing lamp on that speaker begins fast flashing.
    4. Next, power up the second XB10.  Again, its Power / Pairing lamp should start flashing white.  Note that you have one minute to do this after putting the first speaker in Add mode.  Otherwise, that speaker times out, and reverts to a single BT speaker configuration. If this happens, power down both speakers, and start over with step 1.




Pairing Two Sony XB10 Speakers in Double Mode

    1. Press and hold the Add button on the second speaker for approximately three seconds, until this XB10 beeps. The Power / Pairing lamps on both speakers should be flashing white now, and the units are now functioning as a single Bluetooth speaker. You’ll also see the L and R lamps on both speakers glowing steadily. These lights tell you which speaker will play the left stereo channel, and which will play the right. When you make the initial connection between the speakers though, Double Mode is the default.  So both L and R lights glow white on both speakers.

Pair to the Speaker Set Just Created

iPadOS Bluetooth Settings screenshot, showing the Sony XRS XB10 speaker as discovered.
iPadOS Bluetooth Settings screenshot, showing the Sony XRS XB10 speaker as discovered.
    1. Then, pair your Bluetooth source device to your XB10 speaker set that you just created.
    2. Set the volume to a moderate level using the controls on either speaker.
    3. Begin playing something on your BT source device, and you should hear it play on both XB10 speakers.
    4. Then, adjust the volume using the controls on one or the other speaker.  Adjusting volume on one also changes it on the other.
Screenshot of the iPadOS Bluetooth page, showing the Sony XB10 connected.
The iPadOS Bluetooth page, showing the Sony XB10 connected.

Switching Between Double Mode and Stereo Mode

    1. To switch between Double Mode and Stereo Mode, press and release the Add button on one of the speakers. When in Double Mode, each speaker plays a mono version of the content, which contains both the left and right channels.  So in this mode, both the L and R lamps light up on both speakers.  But in Stereo Mode, one speaker plays the left channel while the other plays the right.  The L light on the left speaker glows in this case while the R lamp is OFF.  The reverse happens on the right speaker in Stereo Mode.  That is, the L lamp is OFF and the R lamp is ON.

How to Break the Stereo Connection

To end this speaker tethering, press and hold the ADD button on one of the speakers until you hear a beep (approximately 3 seconds). The L and R lamps on both speakers then go dark, and this signals that you have now dissolved the pairing.

Other Sony XB10 Posts

    1. How to Check Sony XB10 Battery Life
    2. Sony XB10 Charging Instructions
    3. How to Put Sony XB10 in Pairing Mode
    4. How to Charge Sony XB10
    5. How to Turn On Sony XB10

References for Sony XB10 Pairing Two Speakers

    1. Sony XB10 Official Support Page
    2. Where to Buy the Sony XB10

Revision History

    • 2023-03-14: First published.