Batteries

How to Check Battery Of Ultimate Ears Wonderboom 2

Shows how to check battery of Ultimate Ears Wonderboom 2, and also how to tell if the battery is losing capacity over time.  When you press the right buttons while the speaker is running, it emits one or more sound pulses to tell you how full the battery is, as described below.

How to Check Battery of Ultimate Ears Wonderboom 2: Step by Step

1. First, Power Up the Ultimate Ears Wonderboom 2

You won’t be able to read battery unless the speaker is ON.

The Top of the Ultimate Ears Wonderboom 2. Showing the dark -Power- button.

To turn on the speaker, press and release the Power button, pointed out by the yellow arrow the last picture.

The small lamp in that button should then light, as we see next, and the speaker should make its startup sound.  If it does not, then the battery could be completely dead.

Top view of the speaker, powered ON, with its -Power-button lit.

But as long as there’s some energy in the battery, the speaker should boot.  When it does, move ahead to the next step.

2. Press and Release the Volume UP and Volume DOWN Buttons

Press and release the center areas of the Volume UP and Volume DOWN buttons at the same time.  Find these areas in the picture shown next. The Volume Up button is in the center of the plus (+) symbol on the speaker front, and the Volume Down button is found in the middle of the vertical minus (-) symbol, just below the plus symbol.

The two buttons you press to check current battery charge.

When you press these buttons together, the speaker makes one to four “blunk” sounds to tell you how high the battery is.  Four blunks means that the battery has between 75 and 100 percent charge.  Three blunks, and the battery has between 50 and 75 percent charge.  Two blunks denotes that you have between 25 and 50 percent charge in the speaker’s battery.  And finally, one blunk means between 0 and 25 percent charge.

About the Red Power Light

Also, when the Ultimate Ears Wonderboom 2 battery gets critically low, the Power lamp starts flashing red, as shown next.

Front top view of the Ultimate Ears Wonderboom 2. Showing the red light glowing. This means that the battery is getting pretty low.

Press these buttons any time the speaker is ON, to check the battery.  The number of blunks you hear, lets you roughly guess how much time you have left to play the speaker, before it goes dead.  Since a fully charged Wonderboom plays for roughly ten hours.  So four blunks means that the speaker has between 7.5 and 10 hours of play time left before it goes dead.  Three blunks means that it will play for another 5 to 7.5 hours.  Two blunks means between 2.5 and 5 hours of music time left.  And 1 blunk means that you’ll get between 0 and 2.5 more hours of play time.

Other Ultimate Ears Wonderboom 2 Posts

    1. How to Reset
    2. Bluetooth Pairing Directions
    3. Charging Instructions
    4. The Watt Numbers

References for How to Check Battery of Ultimate Ears Wonderboom 2

    1. Official Ultimate Ears Wonderboom 2 Support Page
    2. Where to Buy the Ultimate Ears Wonderboom 2
admin

Recent Posts

How to Connect Honeywell WiFi Thermostat to Network

You might need to know How to Connect Honeywell WiFi Thermostat to Network for the…

12 mins ago

How to Connect Honeywell Wireless Thermostat to Router

You might need to know How to Connect Honeywell Wireless Thermostat to Router for the…

19 mins ago

Connect Honeywell Thermostat to WiFi

You might need to know the Connect Honeywell Thermostat to WiFi procedure, to do this…

49 mins ago

How to Connect Honeywell Thermostat to WiFi

You might need to know How to Connect Honeywell Thermostat to WiFi for the first…

1 hour ago

How to Connect Honeywell Thermostat to Router

You might need to know How to Connect Honeywell Thermostat to Router for the first…

1 hour ago

How to Connect Honeywell WiFi Thermostat to Router

You might need to know How to Connect Honeywell WiFi Thermostat to Router for the…

1 hour ago