Front view of the JBL Boombox BT speaker.
Many JBL speakers, including the Boombox, have a blinking red light when the battery is almost dead. We find this lamp in the battery gauge on the front lower center of the boombox grill. Sometimes though, this red LED flashes for long periods as you play the speaker. So it begins pulsating during play and does not stop, even when you connect a charger. Thus in this post, we offer reasons that this can happen. Then we give possible fixes.
It’s normal that the battery gauge displays a blinking red light when the juice left in it is very low. But this meter should turn white when you connect the speaker to a charger, and battery recharging begins.
Normally though, this gauge only shows white lights. The number of lamps that glow tells you how full the battery is.
Or, once recharging finishes, all lights in this gauge go out.
Now the blinking red lamp in this meter may not change to white when you connect the charger. If not, then several things might cause this. We list these below thus.
The power adapter may not deliver any power because it is not getting any to begin with. This can happen due to a defective AC or car circuit or tripped circuit breaker. Furthermore, a blown fuse, faulty wiring, or general power outage might be to blame.
Check that your outlet has electricity by testing it by plugging in a lamp or other device. Reset circuit breakers if tripped. Change the bad fuses, and if the outlet has a light switch that controls it, then flip that switch ON.
The JBL Boombox red light continues blinking perhaps because your adapter provides SOME but not ENOUGH current. Its output energy can fall over time. So it might not deliver the correct amount if very old. Note that the boombox requires 4.0 amps 20 volts (80 watts) to fully recharge in the shortest time.
The solution is to replace the adapter, preferably one that delivers at least these exact values. In this case, get from JBL the exact replacement power supply for this boombox. Thys avoids possible damage to the speaker or the supply itself.
The Problem
As lithium ion batteries age, they lose their ability to fully recharge. Plus, the characteristics of the current they draw changes as they get older. Normally, as a battery recharges, it draws less current as it charges. But in the case of cell failure, it may draw too much or too little amperage. Thus this can confuse the charging circuits. So they may behave like no charging is occurring even with voltage present. So, the red lamp keeps blinking.
To fix this, replace the battery. But keep in mind that you can’t easily get to it in the Boombox 1. Indeed, changing the battery means that you must teardown the speaker.
But note that doing this likely breaks the water resistant seal. Thus the speaker will no longer be safe to use, if you get water on it.
Breaking this seal may also change the sound quality too. So get someone to replace the battery who knows how to pick the right replacement. They should also be able to restore the seal to as it was, as they reassemble the speaker. A good battery should fit well inside.
Even if you have the correct power supply, the current getting to the battery may be too low or high. This can happen when the battery management circuits fail. Note that normally these systems read the battery status. Then they shut off the charging current when they deem the battery full.
But when they break, the battery might get no power at all. Thus, it never recharges. Again, in this case, the red light might never stop blinking, even with the charger online. The Boombox may also not play as long before going dead. Or it might not play at all, except when charging.
The best solution here, is simply to get a new speaker. Why? Because the circuits in this model are rather small. So unless you can replace the system board(s) yourself, your best bet is to just buy another speaker. But be sure to recycle your old one though.
You may experience Wi-Fi connection errors when booting your original Google Home speaker. Or, the…
The JBL Charge 3 features several controls and lights across its top, as well as…
Here we give the hard reset Google Home Mini speaker routine. You might hard reset…
You can hard reset all of the smart speakers in the Google Home family. These…
Covers How to Hard Reset Google Home. Now you can reset this original version of…
Gives the iPod Touch hard reset procedure. Now a hard reset restores all settings to…