JBL Clip 3 Red Light Stuck ON

JBL Clip 3 Bluetooth wireless speaker, top view, status lamp glowing red.

Many speakers, including this one, feature a status light that glows red while charging / recharging. Sometimes though, this JBL Clip 3 red light is stuck ON. So it does not turn off once charging completes. In this post, we propose reasons that this happens and possible fixes for this common problem.

JBL Clip 3 Red Light Stuck ON: Why This Happens

It’s normal that this red light glows while the Clip 3 charges. Recharging can take up to a few hours, until the battery completely fills up. Then, under normal circumstances, this light should switch off, or turn to white if the unit is running.

JBL Clip 3 top view, showing the status lamp glowing white.

The dark -Status- lamp.

If the red lamp does not change to white or go dark, a couple things might cause this.

1.The AC or Car Outlet May Not Have Power

The Problem

The AC or car adapter for the JBL Clip 3 may not deliver any power because it is not receiving any to begin with. This can happen due to a defective AC or car circuit, tripped circuit breaker, blown fuse, faulty wiring, power failure, and the like.

The Fix

Check that your outlet has power by testing it by plugging in a lamp or other device. Reset circuit breakers if tripped, and if the outlet has a light switch that controls it, then be sure that that switch is in the ON position.

2. Power Supply is Too Weak or Defective

The JBL Clip 3 red light stays on perhaps because the charging adapter you’re using provides SOME but not ENOUGH charging current. Or, the output power has weakened over time. The Clip 3 requires at least 0.6 amps of charging current at 5 volts (3 watts) from the supply to fully recharge in the specified time.

The fix is to replace the adapter, preferably with a higher output model.

3. The USB Charging Cord is Too Long, Thin, or is Defective

The USB cable can reduce the charging current even if your power supply is working correctly. This might happen with excessively long or thin cables.

To solve this, use as short a cord as is practical. Or, upgrade to a thicker, higher current handling cable. We suggest keeping cable lengths to six feet or less, and to choose a cable that is certified to carry at least 1.0 amps.

4. The Internal Battery Needs Replaced

As lithium ion batteries age, they lose their ability to fully recharge, and the characteristics of the charging current they draw changes as they get older. Normally, as a battery charges, it draws less and less charging current. We suspect that the unit monitors this. And when the charge current falls to a value that it interprets as battery fullness, then it shuts off the red light. But a faulty battery may not behave this way, and continue drawing higher current. So in this case, the current never falls to the fully charged value, and so the red lamp never turns off.

To fix this, replace the battery, although you can’t easily get to it in the JBL Clip 3. Changing the battery requires that you disassemble the speaker. Note that doing this likely breaks the waterproof seal. So the unit no longer resists damage due to wetness.

Breaking this seal may also change the sound characteristics as well. Thus, we suggest that you leave battery replacement to someone who can pick the right replacement battery, and is able to restore the seal as they reassemble the Clip 3. A good battery should fit inside and provide 3.7 volts and at least 1,000 mAh (3.7 watt-hours). But we suggest using only JBL certified replacement batteries for this speaker.

5. JBL Clip 3 Red Light Stuck ON: Because You May Need to Replace the Unit

Even if you have an adequate power supply and cable with a working battery, the charging current that actually reaches the battery may be too low or too high. The can happen when the battery management electronics inside the Clip 3 fail. These circuits monitor the battery and shut off the charging current when they deem the battery to be full. But when they go bad, the battery might receive no charging current at all, and thus never recharge. Again, in this case, the red light might never turn off while charging. You would also notice that the Clip 3 doesn’t play as long before going dead. Or it might not play at all except when you’re charging it.

The most practical solution here, given the relatively low cost of the JBL Clip 3, is simply to get a new JBL Clip 3. Why? Because the circuits in this model are quite small. So unless you can replace the system board(s), or know of a cheap way to do it, just buy another unit.

Front view of the JBL Clip 3.