Factory Reset Amazon Dot

The Amazon Dot assistant speakers need a factory reset every now and again. This restores them to out-of-box, factory default state. Amazon resetting also fixes many bizarre behaviors they sometimes act out.  Furthermore, resetting prepares the speaker assistants for sale or gifting. So here, we offer these Factory Reset Amazon Dot instructions for these little smart speakers.

Factory Reset Amazon Dot 1: Step by Step

1. Power Up the Dot 1

Connect the 1st Gen Dot to its USB power cord.

The light ring then lights up blue for a bit, and then goes out once the Dot finishes booting.

2. Press the Dot 1 Reset Button

Once the light ring goes black, press in and hold the Reset button with a sharp object like a paper clip or pen tip. Press for five to ten seconds.

Then, release when the light ring turns orange, and then blue.

3. Wait for Reset to Finish to Continue with Factory Reset Amazon Dot

After a several-seconds pause, the light ring goes black for a short time.

Then it turns orange.

4. Reset Now Done

You have now restored your Dot 1st Gen speaker to its factory default state. The unit enters Setup mode after that.

Factory Reset Amazon Dot 2: Step by Step

1. Connect your Dot 2 to Power

Plug the Dot 2 into its USB power adapter, and then the adapter into a wall outlet.

The light ring glows blue for a time, and then goes dark. This means good boot up.

2. Press the Dot 2 Reset Button Combo

See our  Where is the Alexa Echo Dot Reset Button  post, for details on how to find the  Reset  button on the 2nd gen Dot. At any rate, once the light ring goes black, press and hold the   Mic Mute   and   Volume Down   buttons. Press these at the same time for the same amount of time.

3. Wait for Reset to Finish to Continue with Factory Reset Amazon Dot

After a several-seconds pause, the light ring again goes black for a brief pause, and then glows orange.

4. Dot 2 Reset Now Done

You have now reset your Dot 2 speaker and returned it to its factory default settings.

Then, it enters   Setup   mode.

5. Done!

Factory Reset Amazon Dot 3rd Generation

1. Attach Wall Power Cable

First, connect the Dot 3rd Gen speaker to its 12-volt power cord, as shown next.

2. Next, Plug the Power Pack into a Working Wall Outlet

See this as shown next.

Then, wait for the Dot to finish powering up.  It’s done when either the light ring goes completely dark, or it begins flashing orange, red, or purple.

3. Then, Press and Hold the  Action Button for 5 to 10 Seconds to Continue with Factory Reset Amazon Dot

Depress the  Action button until the light ring turns orange, and the smart speaker says that it is going into   Setup mode.  On this model, the   Action  button doubles as the   Reset   button, and is pointed at by the green arrow in the next picture.

4. Finally, What Happens After Factory Reset Amazon Dot ?

You have now restored your Dot 3 assistant speaker to factory default settings.  It then enters   Setup   mode afterwards, as shown next.

Set Up Again or Give, Sell It

You may now unplug, pack, and give your  Dot to someone else. Have no fear that they’ll see your account settings on your personal Amazon account. Those values have now left the the speaker.

Or, you can set it up once again on your account and WiFi. Once the light ring turns orange, the unit stays in   Setup   mode until set up again. The Dot will not work until set up and linked to the internet.

Other Posts About Amazon Dot Speakers

1. 1. Echo Dot 3 Setup Instructions for Amazon Alexa 3rd Generation Dot
   2. Amazon Dot WiFi Setup Instructions
   3. Alexa Echo Dot Spotify Instructions, Setup, Play
   4. Restart Echo Dot, How To Restart Amazon Dot
   5. Connect JBL Speaker to Echo Dot, How To

References for Factory Reset Amazon Dot

1. 1. Alexa Official Home Page
   2. Where to Buy an Amazon Dot