Picture of the Netgear EX3700 AC750 Wi-Fi range extender, showing the front lights prior to connecting to primary router.

Netgear Extender Factory Reset Instructions

In this post, we give Netgear extender factory reset routine.  Indeed, Netgear® builds a vast line of network extenders. And many have a factory reset button.  Thus when you press this button, it  causes the unit to erase any custom settings. Factory reset then returns the extender to factory default values. E.g. A factory reset restores the settings to what they were when the unit shipped from the factory.

So you factory reset the Netgear extender to factory default state if it shows strange behaviors.  These could include failing to link to the primary Wi-Fi network.  Or, the extended or extension network slows or freezes, and so on.  Try factory resetting before buying a new unit.  A simple factory reset might save you the cost of that  new extender.

Thus, here, we offer a simple method to do this, and hopefully, a factory reset will fix most problems you might see in this equipment.





Netgear Extender Factory Reset Directions

1. Find Good AC Power

Never interrupt power during the factory reset.  Why not?  Because this can spoil the extender’s memory or break the firmware inside.  Thus, the extender may not boot afterwards.  So, we suggest plugging your Netgear extender directly into a well-fitting and non switched AC wall outlet.  Moreover, do not attach it through an extension cord because this avoids the loose and spotty connections often found in cheap or worn out cords.

2. Power On your Netgear Extender

Wait until the extender finishes booting before advancing to the next step.  Normally, booting can take between thirty seconds and one minute.

3. Write Down Any Extender Settings you’ve Changed to Continue with Netgear  Extender Factory Reset

Save any changed settings you’ve made to the extender before factory reset.  These could include the extended WiFi network name, password, network channel numbers used, and so on.  Since the extender clears these settings during factory reset, write them down first.  You’ll need this settings list after the unit comes back up.  With it, you can easily apply them again if you wish.





4. Start Factory Reset by Either of Two Ways

If you want to use the physical reset button, skip ahead to step 9.  Or, do a factory reset via the device’s admin web pages. Many Netgear® extenders give both options).

To factory reset via the web, go on to the next step.  Doing it this way saves you from having to dig it out from behind furniture to get at its reset button.  But using the web may not always be easy, like when the unit freezes or locks up. So, choose how to reset based on your specific situation.

Netgear Extender Factory Reset via the Netgear® Genie® Web Site

Picture of a common Netgear extender, displaying the Genie first page for Setup.
A typical Netgear extender displaying the Genie first page for Setup.

1. Log In to the Netgear Extender’s Admin Web Site

Once the extender powers up and fully boots, connect a computer to it.  Then, on that computer, bring up a web browser.  Then, visit the  http://mywifiext.net/  site.  The Netgear® Genie® web site front page then displays.

Then, follow the prompts through the extender login to the site.

2. Find the Factory Reset Option 

You often find the factory reset link under the Settings->Other section.

3. Click the Factory RESET Button

This brings up a restore factory defaults confirm prompt screen.  You may choose not to factory reset the extender at this point.  In that case,  just leave the reset page.  But if you still wish to factory reset, move on to the next step.





4. Click the YES Button to Continue with Netgear Extender Factory Reset

Clicking or tapping this link is like pressing the reset button on the unit. That is,  factory resetting takes the Netgear extender offline while it restores the factory default settings.

Now the extender will also log you off of the http://mywifiext.net/ web site during this time. Lights will go out for some seconds, then start flashing as the reset takes effect.

5. Done with Netgear Extender Factory Reset via the Web Site !

Now, you may move your extender to a new spot and set it up there.  Or, it’s now ready for the next user if you’re going to sell or gift it.

Netgear Extender Factory Reset with its RESET Button

1, Find the RESET Button

The button is quite small. Furthermore, you often find it inside a hole on either the back or bottom of the extender.  The button is red, black, or silver in color, and likely in a hole in the case surface. Use a flashlight if you put your unit in a dark spot.

2. Press and Hold the RESET Button for Ten to Twenty Seconds

Since the RESET button port is often small, use the tip of a pen or paper clip to reach it.  Also, this button is delicate. So, if you poke it too hard, you can easily jam or break it.  Thus increase your pressing pressure only until you feel the button give (click) into the pressed position.  Then, keep pressing with that same strength until the extender starts resetting.





3. Release the RESET Button to Continue with How to Netgear Extender Factory Reset

You can tell when factory reset begins because the lights will all go out, except for perhaps the Power lamp.  You need not keep holding the button in, once this process starts.  In fact, pressing for too long can, again, damage the button.  So, only hold it in as long as it takes to start factory resetting.

4. Wait for the Extender to Finish Factory Resetting

This can take up to four minutes.  So stay calm, and DO NOT UNPLUG (POWER DOWN) YOUR EXTENDER WHILE RESETTING!!! 

Again, turning off most any network device while it’s resetting can brick it. If that happens, you may have to send the extender to Netgear® for proper re flashing. That is,  if they can re flash at all.  For cheaper extenders, factory re flashing may not be worth the expense.  So, get it right the first time.  That is, never stop a extender while factory resetting.

Factory reset is done when the lights stop blinking.  You should also see the extender’s admin setup web pages at http://mywifiext.net/  after reset.

5. Reapply Any Customized Settings

Once the factory reset is done, make any changes to the extender’s settings that your specific network might need, at the http://mywifiext.net/ site.

6. Done with Netgear Extender Factory Reset Using the RESET Button !

What ever way you reset your Netgear extender, it is now ready for setup.  Note that you must set up your extender anew after a factory reset.  It will not extend any networks until you enter the wireless networks you wish to extend.  Do this on the extender’s setup web pages.





Related Posts to How to Netgear Extender Factory Reset

  1. JBL Charge 4 Factory Reset Instructions
  2. JBL Xtreme 3 Factory Reset Instructions
  3. Amazon Echo Factory Reset Instructions
  4. Echo Spot Factory Reset Instructions
  5. JBL Flip 4 Factory Reset Instructions

Revision History

  • 2021-08-08: First released.
%d bloggers like this: