Follow these instructions that show how JBL Charge 3 charging via its hidden DC input charging micro USB port works. Discussed below.
JBL Charge 3 Charging First Remarks
First, we recommend recharging the JBL Charge 3 with the included JBL USB charger. Why? Because this power adapter meets the speaker’s amperage needs, and is provided by JBL besides. Presumably, JBL thinks that this is a well-matched AC charger. So, we won’t buck any systems here, although in a pinch, you could fully recharge this power bank speaker with other non JBL wall adapters. But exploring those options is beyond the scope of this post.
JBL Charge 3 Charging, Frequently Asked Questions (FAQ)
When is it Time to charge the Charge 3 JBL Speaker?
You know that it’s time to charge the JBL Charge 3 when the battery status gauge near the bottom on the front of the speaker shows a single flashing red light, or simply, when the speaker stops playing. 🙂
When you see that flashing red, connect the orange USB jack included with the speaker between the Charge 3 and the power adapter. Then, plug the supply into a working AC outlet, to keep the music going.
Finally after four hours or so, your Charge 3 fully recharges. Then, you can play it again for roughly twenty hours before it runs dead again.
What’s the JBL Charge 3 Charging Time?
This speaker fully recharges in approximately four and a half hours, depending on the state of the power bank battery when charging begins, and the charger used to juice it up. We assume that you recharge this speaker with the charger that accompanies it. Other AC USB chargers may take more time to fully recharge the speaker.
Why Does my JBL Charge 3 Keep Shutting Off?
An older battery often causes unexpected shutdowns, as it can no longer output the minimum current the speaker needs to work properly. Installing a new battery can solve this problem. We suggest though, that you get with a qualified electronics technician to perform this battery installation.
What Does the JBL Charge 3 Red Light Flashing Mean?
When you see the red light blinking on the Charge 3’s battery status gauge, the battery has very little electricity left. So the speaker will shut off within an hour (approximately) if not recharged. Note though that this light never flashes red when a working charger power supply is connected and powered on. As you recharge the Charge 3 from a completely dead state, this lamp switches from flashing red to blinking white.
JBL Charge 3 Charging, Step-by-Step Instructions
1. For Best Results, Use the Included USB Power Adapter
As stated earlier, we’re using the JBL USB wall charger AC adapter included with this speaker, as shown next.
2. Open the Port Door
Pry open the port door flap on the lower back of the Charge 3, and pull it toward you to open all the way. This exposes the USB power out and micro USB charging input ports inside, as shown next.
3. Plug in the DC Power Cord to the Charge 3
Then, plug the USB connector end of the charge cord into the matching micro USB input port on the speaker, as shown next.
4. Plug the AC Power Adapter into a Working Wall Outlet, to Continue with JBL Charge 3 Charging
Now that the Charge 3 and its AC adapter are connected, we plug the wall charger into a functioning AC outlet, as shown next.
At least one of the battery status lamps lights up on the Charge Three when you apply charging power. There are five lamps on the Charge 3 that come on in succession as battery recharging progresses.
5. Allow the JBL Charge 3 to Recharge Until All Battery Power Lights Go Off
Battery charging is almost complete when all but the last of the battery status lights light solid. The last one continues to blink for several minutes more to top off the charge, as shown next.
The battery recharge cycle finishes when all battery status gauge lights go out, as shown next.
6. Unplug the USB Charging Cable from the Charge 3
The next picture shows the USB charging port after we removed the charge cord.
7. Fully Push Closed the Water Resistant Port Door to Continue with JBL Charge 3 Charging
Note that unless this power port opening flap is completely closed, water could enter the input and output connector ports area, and likely damage the Charge 3’s electronic components inside. So, take great care to correctly seat the port door on this speaker This way, you get the full water resistance protection the speaker was designed to offer.
See how this port door looks when fully closed and sealed in the next picture.
8. Charging JBL Charge 3 Speaker Power Bank Done!
We have now fully charged our JBL Charge 3 Bluetooth speaker. Note that the battery status gauge just after turning on the Charge 3 following a full recharge. All lamps glow, meaning that the speaker is indeed charged to full, as shown in the next picture.
Repeat this recharging exercise every twenty hours of music play to keep the battery power bank in ready-for-use condition. We charge ours when the battery status gauge lights show just one lamp glowing. Keeping this speaker charged is important if you charge your phones / tablets from it.
Related Posts to JBL Charge 3 Charging Instructions
Other Posts About the JBL Charge 3 Portable Speaker
- 2022-12-02: Updated links.
- 2020-04-21: Added more tags.
- 2019-05-14: Tweaked the targeting for ‘JBL Charge 3 Charging’.
- 2019-02-10: First posted.